Colloidal silver generator production nanosilver

Colloidal silver generator production nanosilver

Promotional offer on microprocessor colloidal silver generator GSK-2 GREEN (30V, approx. 3.5mA, version for 4 electrodes).

600PLN

Technical specifications

Condition
New
Invoice
VAT invoice issued
Model
Srebro koloidalne generator produkcja nanosrebro
Manufacturer
Nowoster

Product description

Promotional offer on microprocessor colloidal silver generator GSK-2 GREEN (30V, approx. 3.5mA, version for 4 electrodes). High quality colloidal silver production. Colloidal silver (nanosilver) has disinfectant properties. Reusable masks can be soaked in silver to increase protective effectiveness.

Included in the set:

  1. GSK-2 GREEN generator
  2. 9V or 12V power supply
  3. Banana plugs 4 pcs

To produce high-quality colloidal silver it is best to:

  1. Use silver wires of minimum 999 fineness. Wires must be purchased separately.
  2. Ultra-pure distilled or demineralized water with a maximum foreign ion content of 2ppm must be used to produce colloidal silver. Tap water, mineral water, etc. must not be used. Good water includes, among others, Kamix distilled water and Orlen Aqua Tech demineralized water (available at Orlen petrol stations).
  3. Use glass or ceramic vessels preferably. Metal vessels must not be used.
  4. Electrodes must not touch the bottom or walls of the vessel. The vessel must be clean.
  5. A TDS meter is best for checking water purity and final concentration.
  6. Do not mechanically stir the colloid during the production process.
  7. It is recommended to clean electrodes of deposits (dark gray deposit) every 2-3 hours with a kitchen towel, tissue, cotton cloth, etc.
  8. Production should be carried out in a dark place at room temperature. Heating during the process is permitted. Must not be in a sunlit room.
  9. Every few liters it is recommended to polish silver wires with fine sandpaper to a shine
  10. Store colloidal silver in a dark glass container in a dark place at room temperature.

Main features of the generator Current limit - approx. 3.5mA Maximum output voltage - 30V Electrode spacing - approx. 5cm Electrode polarity reversal Automatic voltage reduction on electrodes when current is limited Generator designed for silver electrodes from 2 to 2.5mm diameter and from 10 to 15cm length Typically the generator can produce up to 15ppm at full immersion or 20-25ppm at partial electrode immersion. Production rate is approx. 1ppm per 1-2 hours depending among other things on water volume and purity and wire size. Description of GSK-2 GREEN colloidal silver generator power supply in the range 9-12V DC. 9-12V power supply included in the set. current draw approx. 70mA. Power consumption approx. 0.8W. short-circuit protection for electrodes overload protection adjustable end-of-process trigger threshold based on voltage on colloidal silver electrodes. For current limiting, as CS concentration increases the microprocessor lowers the voltage. For a given concentration and set threshold (on the potentiometer) the process will end. End-of-process indication is smooth LED pulsing. The closer to the end of the process, the faster the LED will flash. If the concentration obtained is too low, turn the potentiometer to the right. If too high - turn to the left. For the same vessel and the same amount of water, similar concentrations will be achieved. For example: for the middle potentiometer position and a glass of water, a CS concentration of approx. 7-12 ppm will be achieved fully electronic polarity reversal. Reversal time is fixed and is approx. 1 minute. dimensions in housing 9.5cm by 5cm. Height 4cm. Colloidal silver production Pour approx. 800ml of ultra-pure water into a clean dry vessel, e.g. a 0.9 liter jar. Place the generator on the vessel so that the electrodes are as fully immersed as possible. Do not submerge the plugs. Connect the power supply to the mains. Production may take several to over ten hours. During the process the LED flashes. Near the end the LED flashes faster. When the LED pulses (dims and brightens within approx. 1s) the generator has disconnected voltage from the electrodes and will not produce a higher concentration. Check the concentration with a TDS meter. During production it is recommended to clean the electrodes. If too low, disconnect and reconnect the power supply to reset the timer in the generator. The generator is designed for the best quality and typically produces up to 15ppm. The best quality of colloidal silver produced is between 5 and 15ppm. During production the electrodes will be covered with gray deposit (silver oxides). After the process is complete, filter the colloidal silver well (e.g. through a coffee filter) to remove deposits. The appearance of deposits is normal. Electrodes should be evenly covered with gray deposit.