Colloidal silver generator colloid GSK-1 RED + wires
Set

Colloidal silver generator colloid GSK-1 RED + wires

Promotional offer on microprocessor colloidal silver generator GSK-1 RED. High quality colloidal silver production.

650PLN

Technical specifications

Condition
New
Invoice
VAT invoice issued
Model
GSK-1 RED
Manufacturer
Nowoster

Product description

Promotional offer on microprocessor colloidal silver generator GSK-1 RED. High quality colloidal silver production.

Included in the set:

  1. GSK-1 RED generator
  2. 9V or 12V power supply
  3. Silver wires 999 2mm 10cm 2 pcs

To produce high-quality colloidal silver it is best to:

  1. Use silver wires of minimum 999 fineness.
  2. Ultra-pure distilled or demineralized water with a maximum foreign ion content of 2ppm must be used to produce colloidal silver. Tap water, mineral water, etc. must not be used. The best water includes, among others, Kamix distilled water and Orlen Aqua Tech demineralized water (available at Orlen petrol stations).
  3. Use glass or ceramic vessels preferably. Metal vessels must not be used.
  4. Electrodes must not touch the bottom or walls of the vessel. The vessel must be clean.
  5. A TDS meter is best for checking water purity and final concentration. TDS meter must be purchased separately.
  6. Do not mechanically stir the colloid during the production process.
  7. It is recommended to clean electrodes of deposits (dark gray deposit) every 2-3 hours with a kitchen towel, tissue, cotton cloth, etc.
  8. Production should be carried out in a dark place at room temperature. Heating during the process is permitted. Must not be in a sunlit room.
  9. Every few liters it is recommended to polish silver wires with fine sandpaper to a shine
  10. Store colloidal silver in a dark glass container in a dark place at room temperature.

Main features of the generator Current limit - approx. 2.5mA Maximum output voltage - 30V Electrode spacing - 4cm Electrode polarity reversal Automatic voltage reduction on electrodes when current is limited Generator designed for silver electrodes from 2 to 2.5mm diameter and from 10 to 15cm length Typically the generator can produce up to 15ppm at full immersion or 20-25ppm at partial electrode immersion. Production rate is approx. 1ppm per 1-2 hours depending among other things on water volume and purity and wire size. Description of GSK-1 RED colloidal silver generator power supply in the range 9-12V DC. 9V or 12V power supply included in the set. current draw approx. 50mA. Power consumption approx. 0.6W. short-circuit protection for electrodes overload protection adjustable end-of-process timer in the range approx. 30 minutes to approx. 8 hours (left potentiometer P1 in the photo, left position is minimum time and right position is maximum time). End of process is indicated by the LED through smooth (gentle) pulsing. During operation depending on remaining time the LED flashes intermittently (on, off). Flash frequency depends on remaining time and is in the range approx. 0.1Hz to 1Hz (once every 10 seconds for long times to once per second for short times). Timer start is always at startup (when supply voltage is applied). Disconnecting and reconnecting power resets the timer and counting starts from the beginning adjustable polarity reversal time for silver electrodes in the range approx. 10-115 seconds (right potentiometer P2 in the photo. Leftmost position is minimum time and rightmost is maximum time) dimensions in housing 5cm (with mounting tabs approx. 7cm) by 7cm. Height 2.5cm. Colloidal silver production Pour 200 to 500ml of ultra-pure water into a clean dry vessel. Place the generator on the vessel so that the electrodes are as fully immersed as possible. Do not submerge the plugs. Connect the power supply to the mains. Production will take several hours depending on the set time. During the process the LED flashes. Near the end the LED flashes faster. When the LED pulses (dims and brightens within approx. 1s) the generator has disconnected voltage from the electrodes. Check the concentration with a TDS meter. During production it is recommended to clean the electrodes. If too low, disconnect and reconnect the power supply to reset the timer in the generator. The generator is designed for the best quality and typically produces up to 15ppm. The best quality of colloidal silver produced is between 5 and 15ppm. During production the electrodes will be covered with gray deposit (silver oxides). After the process is complete, filter the colloidal silver well (e.g. through a coffee filter) to remove deposits. The appearance of deposits is normal. Electrodes should be evenly covered with gray deposit.